Download “OzoneSeal 507 Flyer”
OzoneSeal-507.pdf – Downloaded 247 times – 416.97 KB| Description | OzoneSeal-507 is a two-part flexible waterproofing & protective coating, composed of best quality Portland cement, properly selected & graded aggregates, additives & acrylic emulsion polymer as a binder. OzoneSeal-507 react chemically after mixing to form a hard and flexible film that bonds tenaciously to most concrete or masonry substrates. OzoneSeal-507 prevents intrusion of water, yet allows entrapped moisture to be released. | ||||||||||||||||||||
| Uses | Cast-in-place and pre-cast concrete. Brick, block, stucco, unglazed terra cotta. Porous stone, masonry substrates. Exterior or interior, Above or below grade applications. All types of structures in industrial, commercial and residential areas, coastal environments. To reface and even out variations in concrete surfaces. Wastewater treatment plants. To protect exposed steel rebars from corrosion. As a waterproof coating for roofs. To protect concrete surfaces from carbonation and chloride attack. As a lining for water retaining structures. Potable water tanks. Basements, terraces, balconies and roof gardens. Retaining and sea walls Swimming pools. Sealing hairline cracks, not subjected to movement. As baking to marble, tile, and granite to prevent water ingress and thus alleviate surface staining. |
||||||||||||||||||||
| Advantages | OzoneSeal-507 is highly resistant to standing water or wind-driven rain and is intended for use on. vertical and horizontal surfaces. Waterproof, Allows water vapor to escape from the structure. Highly resistant to the effects of long term weathering. Durable in all climatic conditions. Non-toxic. Excellent bond to concrete and masonry. It does not require overcoating. Flexible. OzoneSeal-507 can be applied on 24-hour old concrete thereby giving immediate protection. Flexible. |
||||||||||||||||||||
| Properties | Typical properties of mixed material:
|
||||||||||||||||||||
| Packaging | 42kg Kit(Powder 25kg+ liquid 17Ltr),25Kg Kit(Powder 15Kg+Liquid 10Ltr) | ||||||||||||||||||||
| Storage | Store in dry and cool place below 35°C. Protect from direct sunlight. | ||||||||||||||||||||
| Shelf life | 12 months if stored properly in original unopened packaging. | ||||||||||||||||||||
| Instruction for use | Surface preparation: All surfaces to be coated must be clean and structurally sound. Chip, sand or shot blast, wet blast or high-pressure water wash to remove all foreign matter, dust, dirt, paints, oils, grease, coatings, laitance or any other surface contaminants. All static cracks or breaks, voids or honeycombing larger than 1/32” should be cut out and repaired with polymer-modified repairing mortar. Mixing: Shake well the liquid component to a homogenous milky color, before mixing transfer entire quantity of liquid component into a suitable clean mixing vessel, gradually start addition of powder component under constant mixing with a stirrer using a pneumatic or electric power tool (1kw) at slow speed at 250 – 300 rpm for 3- 5 minutes to a homogeneous & uniform free-flowing slurry.Application: Pre-dampen the substrate surface with water using a brush or spray bottle. High porosity substrates will require more dampening than dense substrates. Whilst the surface is damp, apply the material using a soft-bristled brush (120mm-200mm wide). Application may also be made by roller, or spray machine. The first coat should be allowed to cure for a minimum of 5 hours at 20°C or 3 hours at 35°C before a second application, should it be required. If overcoating is done more than 24 hours after applying the 1st coat, or the1st coat has already dried out, the surface must be prewetted again. For spray application, the substrate should be prepared in the same manner as for brush application. The required film thickness can be achieved in one application.Coverage: 1.5Kg – 2.5Kg/m2 |
||||||||||||||||||||
| Cleaning & Disposal | All tools and equipment should be washed with water immediately after use. Do not dispose of into water or soil but according to local regulations | ||||||||||||||||||||
| Precautions/Limitations | Do not apply Ozone Seal-507 to surfaces that have not been properly cleaned or are unsound. Do not apply in rain or when rain is expected before initial set has taken place. Do not apply to frozen or frost filled surfaces or when the temperature is below (4°C). For additional Information contact with Ozone construction Chemicals LLC. |
||||||||||||||||||||
| Health & safety | Ozone Seal-507 powder is irritating to the eyes, respiratory system and skin. Avoid inhalation of dust and wear suitable respiratory protective equipment. Ozone Seal-507 liquid is not classified as dangerous. Ozone Seal-507 when mixed, becomes highly alkaline, wear suitable protective clothing, gloves and eye protection. |
WARRANTY: Ozone products are guaranteed against defective materials and manufacture and are sold subject to their standard terms and conditions of sale. Ozone makes no warranties, implied or otherwise, as to the merchantability or fitness for ordinary or particular purposes of its products and excludes the same. If any Ozone product fails to conform to this warranty, Ozone will replace the product at no cost to the Buyer. Replacement of any product shall be the sole and exclusive remedy available and the buyer shall have no claim for incidental or consequential damages. Any warranty claim must be made period from the date of the claimed breach. Ozone does not authorize anyone on its behalf to make any written or oral statements which in any way alter Ozone’s installation information or instructions in its product literature or on its packaging labels. The user of the Ozone products must test the products for suitability for the intended application and purpose before proceeding with the full application of the products.
