Ozone Epocoat WB

Water dispersible epoxy floor coating.

Category:

 

Download “Ozone Epocoat WB Flyer” Ozone_Epocoat_WB.pdf – Downloaded 36 times – 418 KB

Description Ozone Epocoat WB is a two-part, solvent-free, water dispersed epoxy coating. Providing a protective coating which is impermeable to liquids, is abrasion resistant and easy to clean. Ozone Epocoat WB is water-based so it can be applied to damp substrates.
Colors Light Grey, Slate Grey, Mid Grey, Tile Red, Corn, Blue, British Racing Green, Mushroom, Magnolia, Black, White and Clear.
Uses Ozone Epocoat WB is used to provide a protective coating to industrial & warehouse floors subject to light traffic, an oil-resistant coating for bunded areas, a wall & floor coating in the food & other industries requiring high hygiene standards, and a protective coating in sewerage treatment plants.
Advantages Improves working environment.
Suitable for use in areas where solvents are undesirable.
Hardwearing, durable and long-lasting.
Easily and quickly applied by unskilled labor.
Easily cleaned hence reducing maintenance costs.
Can be applied to damp substrates.
Can be used as a curing agent.
Good chemical resistance.
Water based.
Sewerage resistant.
Chemical Resistance O Performance of Ozone Epocoat WB tested by immersion at 20 C against a range of aggressive chemicals.
Acids
Hydrochloric Acid (Conc.) Fair Nitric Acid 25% Good
Sulphuric Acid 50% Good Lactic Acid 10% Good
Acetic Acid 10% Fair Citric Acid 20% Good
Alkalines
Sodium Hydroxide 50% Good Ammonia 10% Good
Solvents
White Spirit Good Methylated Spirit Good
Xylene Good Butanol Good
Oils
Lubricating Oil Good Petrol Good
Skydrol Good
Aqueous Solutions
Sodium Hypochlorite (Bleach) Good Sugar Solution (Saturated) Good
Salt (Sodium Chloride Saturated) Good Ammonium Sulphate (10%) Good

It should be noted that the ability of Ozone Epocoat WB to resist attack is dependent on the temperature and concentration of the chemicals. If in doubt contact the Ozone technical department.

Properties
Pot Life at 20°C 2 hours
Initial Hardness 18-24 hours
Full Cure 5-7 days
Minimum application temp 5°C
Maximum application temp 35°C
Coverage: 5-8 M2 /kg/coat 150 Microns(wet film)
S.G. 1.30
2 Bonding Strength > 1.5 N/mm

 

Packaging 1kg and 2.5kg units
Storage Store in dry and cool place below 35 C. Protect from direct sunlight.
Shelf life 12 months if stored properly in original unopened packaging.
Instruction for use Surface preparation: The surface to be treated should be dry, sound and free from loose materials. Damaged or worn areas should be repaired using Ozone Epo FairCrete. Any laitance should be removed by physical methods or by acid etching. If the strength or the surface stability of the concrete base be in doubt, then we recommend a trial patch of Ozone Epocoat WB is applied to assess its suitability. On highly
polished/power floated floors, mechanical preparation or acid etching will be necessary.Mixing: The base and hardener components of Ozone Epocoat WB should be thoroughly stirred before the two are mixed together. The entire contents of the hardener container should be poured into the base container and the two materials mixed thoroughly at least 3 minutes. The use of a heavy-duty slow speed, flameproof or air driven drill fitted with a mixing paddle is desirable. Mix these components in the quantities supplied taking care to ensure all containers are scraped clean.
Application: The mixed Ozone Epocoat WB should be applied to the prepared surface using airless spray, brush or lambswool roller. Depending on the absorbency of the substrate the first coat may be diluted with up to 10% water by weight to help penetration into the substrate. Do not apply the second coat (or the third if needed) until the previous coating is completely dry. Best results are obtained if subsequent applications are made 24 hours later.
Coverage: The coverage rates depend on the absorption characteristics of the substrate. When applied onto a low absorption and medium roughness surface the coverage rate is approximate as follows.Coating of walls and floors 0.20 kg/m2/coat. (150 micron/coat; minimum 2 coats required)
Cleaning & Disposal Ozone Epocoat  WB should be removed from tools and equipment with Ozone Solvent immediately after use.
Hardened material can only be removed mechanically. Do not dispose of into water or soil but according
to local regulations.
Health & safety Ensure adequate ventilation and avoid inhalation of vapors. Some people are sensitive to resins, hardeners, and solvents. Wear suitable protective clothing, gloves, and eye protection. If working in confined areas, suitable respiratory protective equipment must be used. The use of barrier creams provide additional skin protection. In case of contact with skin, rinse with plenty of clean water, then cleanse with soap and water. Do not use solvent. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice. If swallowed, seek medical attention immediately – do not induce vomiting.

WARRANTY: Ozone products are guaranteed against defective materials and manufacture and are sold subject to their standard terms and conditions of sale. Ozone makes no warranties, implied or otherwise, as to the merchantability or fitness for ordinary or particular purposes of its products and excludes the same. If any Ozone product fails to conform to this warranty, Ozone will replace the product at no cost to the Buyer. Replacement of any product shall be the sole and exclusive remedy available and the buyer shall have no claim for incidental or consequential damages. Any warranty claim must be made period from the date of the claimed breach. Ozone does not authorize anyone on its behalf to make any written or oral statements which in any way alter Ozone’s installation information or instructions in its product literature or on its packaging labels. The user of the Ozone products must test the products for suitability for the intended application and purpose before proceeding with the full application of the products.

Reviews

There are no reviews yet.

Be the first to review “Ozone Epocoat WB”

Your email address will not be published. Required fields are marked *