Download “Ozone Eposcreed Flyer”
Ozone_Eposcreed.pdf – Downloaded 154 times – 414.63 KB| Description | Ozone Eposcreed is a high performance, solvent-free epoxy screed for application to concrete floors where properties of high strength, abrasion, and chemical resistance are required. Suitable for applications within engineering, chemical plants, plating shops, laboratories, loading bays in breweries, dairies, etc., and many other various locations. | ||||||||||||||||||||||||
| Colors | Tile Red, Blue, Light Grey, Slate Grey, Mid Grey, Magnolia, Corn, Mushroom and British Racing Green. | ||||||||||||||||||||||||
| Primary Applications | Heavy engineering plants and steelworks. Electricity substations. Oil refineries and plating factories Warehouses. Heavy loading areas. Airport and parking areas. Car showrooms and mechanical workshops. |
||||||||||||||||||||||||
| Advantages | Excellent general chemical resistance. Hard wearing, abrasion-resistant, durable topping. Joint less screed eliminates potential sources of failure. Good gripping surface for traffic. Suitable for all pedestrian, vehicular and forklift traffic. |
||||||||||||||||||||||||
| Properties |
Note: Where chemical resistance is required or where the screed is laid in areas that are frequently underwater, the system should be sealed using zone Epocoat SF or Ozone Epocoat. |
||||||||||||||||||||||||
| Technical Support | Technical representatives are available to provide further information and arrange demonstrations. | ||||||||||||||||||||||||
| Packaging | 8kg,15 kg,25kg units. | ||||||||||||||||||||||||
| Storage | Store in dry and cool place below 35 C. Protect from direct sunlight. | ||||||||||||||||||||||||
| Shelf life | 12 months if stored properly in original unopened packaging. | ||||||||||||||||||||||||
| Instruction for use | Surface preparation: All surfaces should be clean, dry, free from oil, grease and chemical contamination. Concrete surfaces should be free from laitance which should be removed by grit blasting or scarifying. If it is not practical to grit blast or scarify, it is possible to acid etch the floor. However, precautions must be made to prevent the concrete from absorbing excess moisture. It is recommended that concrete substrates should not have a moisture content of more than 75% RH. This can be assessed using a hair hygrometer covered with polythene for 24 hours as recommended by BS 8203. Should the strength or the surface stability of the concrete base be in doubt, then we recommend a trial patch of Ozone Eposcreed is applied to assess its suitability. On highly polished/power floated floors, mechanical preparation or acid etching will be necessary. Priming: Ozone Epoprime should be used. Mix Ozone Epoprime in the proportions supplied by adding the entire contents of the hardener tin to the contents of the base tin and thoroughly mix. Once mixed this should be applied to the substrate and rolled or brushed well in. If the Ozone Epoprime is totally absorbed the substrate should be reprimed. The Ozone Eposcreed should be applied between 15 minutes and 3 hours after the application of Ozone Epoprime, while the Ozone Epoprime is still tacky.Mixing: The Ozone Eposcreed base and hardener components should be thoroughly mixed in the base container. In cold conditions, it will greatly aid mixing if the materials are stored in warm conditions. Once the base and hardener are thoroughly mixed they should be transferred to a suitable forced action mechanical mixer such as a crete angle the aggregate added slowly. Once all the aggregate is added, mix thoroughly for 3 -4 minutes until a homogeneous mix is obtained. Application: The floor area can be divided into strips one meter wide with timber laths the thickness of the required screed. The Ozone Eposcreed is then laid in strips and worked into previously laid sections and then allowed to harden. The mixed Ozone Eposcreed should be raked evenly over the primed surface and be tamped to ensure complete consolidation, then finished with a float kept clean by wiping with a cloth dampened with Ozone Solvent. Ozone Eposcreed may be carried up the wall to form a coving. Expansion joints in the floor must be maintained and filled with an appropriate joint sealant. In wet areas where Ozone Eposcreed is to be subjected to aggressive chemical attack, it is recommended that the surface be sealed with Ozone Epocoat WB or Ozone Epocoat for added protection. |
||||||||||||||||||||||||
| Cleaning & Disposal | All tools and equipment should be cleaned immediately after use with Ozone Solvent. Do not dispose of into water or soil but according to local regulations. | ||||||||||||||||||||||||
| Precautions & Limitations | Minimum application temperature 5°C. It is recommended that concrete substrates should not have a moisture content of more than 75% RH. | ||||||||||||||||||||||||
| Health & safety | Ozone Eposcreed and Ozone Epoprime, like similar products, are capable of irritating unprotected sensitive skin, we, therefore, recommend the use of a suitable barrier cream and the wearing of gloves and goggles. |
WARRANTY: Ozone products are guaranteed against defective materials and manufacture and are sold subject to their standard terms and conditions of sale. Ozone makes no warranties, implied or otherwise, as to the merchantability or fitness for ordinary or particular purposes of its products and excludes the same. If any Ozone product fails to conform to this warranty, Ozone will replace the product at no cost to the Buyer. Replacement of any product shall be the sole and exclusive remedy available and the buyer shall have no claim for incidental or consequential damages. Any warranty claim must be made period from the date of the claimed breach. Ozone does not authorize anyone on its behalf to make any written or oral statements which in any way alter Ozone’s installation information or instructions in its product literature or on its packaging labels. The user of the Ozone products must test the products for suitability for the intended application and purpose before proceeding with the full application of the products.
